Electric bikes make commuting, recreational cycling, and outdoor adventures more convenient. However, an e-bike is still a motor-assisted vehicle with electrical components, a heavy frame, and higher potential speeds than many traditional bicycles. Riding one safely requires more than knowing how to accelerate and brake.
Whether you are a new e-bike owner or an experienced rider, understanding what not to do on an e-bike can help prevent accidents, protect your battery, reduce maintenance costs, and extend the life of your bike.
From riding without a helmet to charging a damaged battery, some mistakes can have serious consequences. This guide explains 15 common e-bike mistakes, why you should avoid them, and what to do instead.

It also uses the Himiway D5 2.0 20-inch e-bike as a practical example to explain important safety and maintenance considerations.
1. Never Ride an E-Bike Without a Helmet
One of the biggest mistakes e-bike riders make is assuming that short trips or familiar routes do not require a helmet.
Even at relatively moderate speeds, a collision or fall can cause serious head injuries. An e-bike's motor assistance can also make it easier to travel faster than expected, especially when riding downhill or through busy areas.
What to do instead:
- Wear a properly fitted bicycle helmet on every ride.
- Make sure the helmet sits level on your head and the chin strap is securely fastened.
- Replace a helmet after a significant impact.
- Consider additional protective equipment, such as gloves and cycling glasses.
The Himiway D5 2.0 20" features a 750W geared hub motor with 90Nm of torque. Its power makes it important to develop good riding habits and use appropriate protective equipment from the beginning.
2. Don't Accelerate Suddenly Without Preparing
Sudden acceleration is particularly risky for beginners.
When you activate the throttle or pedal-assist system unexpectedly, the bike can move forward before you have fully adjusted your balance. This can be dangerous when starting from a stop, crossing an intersection, maneuvering through pedestrians, or riding in a crowded parking lot.
What to do instead:
- Start with a low pedal-assist setting.
- Keep your hands on the handlebars and fingers near the brake levers.
- Apply throttle gradually rather than pressing it suddenly.
- Practice starting and stopping in an empty parking lot.
- Reduce assistance when approaching intersections and pedestrians.
The D5 2.0 20" offers five pedal-assist levels, an automatic pedal-assist system, and a thumb throttle. Himiway recommends using Pedal Assist Level 0 when starting or approaching intersections to help prevent unexpected acceleration.
3. Never Ride Under the Influence of Alcohol or Drugs
Riding an e-bike after drinking alcohol or taking drugs can seriously affect your judgment, coordination, reaction time, and ability to control the bike.
You may misjudge distances, fail to notice approaching vehicles, or react too slowly to unexpected obstacles.
Even if you are riding on a familiar road, impaired riding puts you and other road users at risk.
What to do instead:
- Never ride after consuming alcohol or recreational drugs that impair your ability.
- Arrange alternative transportation if you are not fit to ride.
- Avoid riding when extremely tired or unable to concentrate.
The U.S. Consumer Product Safety Commission (CPSC) specifically advises against operating micromobility products under the influence of alcohol or drugs.
4. Don't Ignore Traffic Laws and Local E-Bike Regulations
An e-bike does not give you permission to ignore traffic signals, speed limits, or road restrictions.
Some riders assume that every electric bicycle can be used on any bicycle path, sidewalk, or public road. This is not correct.
E-bike regulations vary by state, city, and riding location. Restrictions may cover:
- Minimum rider age.
- Helmet requirements.
- Permitted riding locations.
- Motor assistance and maximum speed.
- Class 1, Class 2, and Class 3 classifications.
- Access to public trails and recreational areas.
What to do instead:
Check your state's e-bike regulations and the rules of the specific trail or park before riding. Follow traffic signals, stop signs, and local speed limits.
For example, the National Park Service allows e-bikes in certain areas where traditional bicycles are permitted, but individual parks can impose additional restrictions.
5. Don't Ride Too Fast for Road Conditions
A powerful motor does not mean you should always ride at maximum speed.
Excessive speed reduces the time available to identify hazards and react to other road users. It also makes tight turns, sudden stops, and uneven surfaces more difficult to manage.
Be especially careful when riding:
- Down steep hills.
- Around sharp corners.
- Through crowded streets.
- On gravel, sand, or loose dirt.
- Across wet leaves or slippery road markings.
- Near pedestrians and parked vehicles.
What to do instead:
Maintain a speed that allows you to stop safely within the visible distance ahead. Reduce your speed before turning, approaching intersections, or entering unfamiliar terrain.
The Himiway D5 2.0 20" has a default maximum speed of 20 mph, with an adjustable speed range shown in its specifications. However, the speed you can legally use depends on the applicable e-bike classification and local regulations.
6. Never Ride With Faulty Brakes
Your brakes are among the most important safety components on an electric bike.
A common mistake is continuing to ride when the brakes make unusual noises, feel weak, or require excessive lever pressure.
This is particularly dangerous on an e-bike because its motor and battery add weight, and higher speeds can increase stopping distances.
What to do instead:
Before every ride:
- Test both front and rear brakes.
- Check for unusual noises or reduced braking power.
- Inspect brake pads and rotors for excessive wear.
- Make sure the brake levers feel firm.
- Check that the motor stops providing power when the brake cutoff is activated.
The D5 2.0 20" uses Tektro hydraulic disc brakes, with a 203mm front rotor and a 180mm rear rotor. These components still require regular inspection and maintenance.
If the brakes are malfunctioning, do not continue riding until the problem has been repaired.
7. Don't Overload Your E-Bike
Carrying too much weight can affect balance, handling, braking, and component durability.
Some riders mistakenly assume that a strong frame or powerful motor means they can carry unlimited cargo or additional passengers.
Every e-bike has a specified maximum payload capacity.
For example, the Himiway D5 2.0 20" has a maximum payload capacity of 440 lbs. This figure includes the rider, cargo, accessories, and other carried weight. Its maximum rider weight is 265 lbs, while the rear rack has a separate 120 lb capacity.
What to do instead:
- Check the manufacturer's payload limit.
- Include your backpack, accessories, and cargo when calculating total weight.
- Distribute cargo evenly.
- Secure luggage properly before riding.
- Never exceed the rear rack's individual weight limit.
- Do not carry another person unless the bike and its approved passenger equipment are designed for that purpose.
Staying within the weight limits helps maintain predictable handling and reduces unnecessary stress on the frame, wheels, tires, and brakes.
8. Don't Charge Your E-Bike With an Incompatible Charger
Using an incompatible charger is a mistake that can damage the battery or create a potential fire hazard.
Lithium-ion batteries require compatible charging equipment. A charger with the wrong specifications may cause abnormal charging behavior and increase the risk of electrical problems.
What to do instead:
- Use only the original charger or a manufacturer-approved replacement.
- Check the charger and battery for visible damage before charging.
- Charge in a dry, well-ventilated location.
- Keep the charger uncovered during charging.
- Disconnect the charger when charging is complete.
- Never charge your e-bike while sleeping or when nobody is home.
For the Himiway D5 2.0 20", the battery is a 48V 15Ah lithium-ion battery, and the supplied charger is designed for this system.
The CPSC recommends using manufacturer-approved chargers and remaining present while charging micromobility products.
9. Never Open, Modify, or Use a Damaged Battery
The battery is one of the most important and expensive components of an electric bike.
Some owners attempt to repair battery packs themselves, replace internal cells, modify wiring, or increase battery output. These changes can compromise electrical protection and create fire or injury risks.
You should also avoid riding with a battery that shows signs of physical damage.
Warning signs include:
- A swollen or deformed battery case.
- Cracks or visible damage.
- Unusual overheating.
- Liquid leaking from the battery.
- Strange smells or smoke.
- Abnormal charging behavior.
What to do instead:
Stop using a damaged battery and contact the manufacturer or a qualified e-bike technician. Use only compatible, manufacturer-approved replacement batteries.
The Himiway D5 2.0 20" manual specifically warns against opening or modifying the battery housing. The CPSC also advises consumers not to use batteries modified by unqualified personnel or assembled with repurposed cells.
10. Don't Ride Through Deep Water or Severe Rain
An e-bike may be designed to handle certain wet conditions, but that does not mean it is waterproof.
Riding through flooded streets, deep puddles, or severe rain can expose electrical components to water and increase the risk of damage.
Wet roads also reduce tire traction and braking performance.
The Himiway D5 2.0 20" has the following water-resistance ratings:
|
Component |
Water-resistance rating |
|---|---|
|
Complete e-bike |
IPX5 |
|
Battery |
IPX6 |
These ratings do not mean the bike can be submerged in water.
What to do instead:
- Avoid flooded streets and deep standing water.
- Avoid riding during severe storms.
- Reduce speed on wet roads.
- Brake earlier than you normally would.
- Dry the bike after exposure to rain.
- Inspect electrical connections if you suspect water intrusion.
Himiway's manual states that light rain riding is possible but does not recommend riding through heavy downpours or flooded streets.
11. Don't Clean Your E-Bike With a Pressure Washer
A pressure washer might seem like an easy way to remove mud and dirt from your electric bike. However, high-pressure water can force moisture into electrical connections, bearings, and other sensitive components.
This can lead to corrosion, electrical malfunctions, or premature component failure.
What to do instead:
- Turn off the e-bike.
- Disconnect the charger and remove the battery if appropriate.
- Use a soft, damp cloth to clean the frame.
- Use a mild, non-corrosive cleaning solution.
- Dry the bike with a clean cloth.
- Make sure the electrical connections are dry before using the bike again.
For the Himiway D5 2.0 20", the owner’s manual specifically advises against pressure washing and submerging the bike in water.
A gentle cleaning routine is generally sufficient to keep an e-bike in good condition.
12. Don't Skip the Pre-Ride Safety Inspection
Some riders get on their e-bikes and start riding immediately without checking whether everything is working properly.
This is particularly risky if the bike has been stored for a long time, transported in a vehicle, or recently assembled.
A loose wheel, low tire pressure, damaged cable, or malfunctioning brake can cause problems during a ride.
What to check before riding:
|
Component |
What to inspect |
|---|---|
|
Tires |
Pressure, tread condition, and visible damage |
|
Brakes |
Front and rear braking performance |
|
Battery |
Proper installation and secure locking |
|
Handlebars |
Correct alignment and tightness |
|
Wheels |
Secure attachment and spoke condition |
|
Lights |
Front light, rear light, and brake light |
|
Chain |
Lubrication and unusual wear |
|
Display |
Normal operation and error messages |
The Himiway D5 2.0 20" owner's manual recommends checking tire pressure before every ride and confirming that the battery is securely attached.
Pay particular attention to the front wheel's quick-release mechanism and the handlebar connections.
13. Don't Ride While Distracted or With Only One Hand on the Handlebar
Using a smartphone, texting, watching videos, or listening to music through headphones can distract you from important road conditions.
You may fail to notice a vehicle turning, a pedestrian crossing, or an obstacle in front of you.
Riding with one hand for extended periods also reduces your ability to respond quickly.
What to do instead:
- Keep both hands on the handlebars whenever possible.
- Never text or operate your phone while moving.
- Avoid headphones that prevent you from hearing surrounding traffic.
- Put personal belongings in a suitable bag or secured rack.
- Stop in a safe location before checking your phone.
- Signal turns before changing direction.
The CPSC recommends keeping both hands on the handlebars and keeping objects off them. NHTSA also advises cyclists to avoid electronic distractions while riding.
14. Don't Ride at Night Without Proper Lighting
Poor visibility increases the risk of collisions because drivers, pedestrians, and other cyclists may not see you in time.
Simply wearing dark clothing and relying on streetlights is not a safe strategy.
This is especially important when riding on roads with limited lighting or during fog, rain, and dusk.
What to do instead:
- Use a working white front light.
- Use a red rear light.
- Keep your reflectors visible and unobstructed.
- Wear reflective or brightly colored clothing.
- Reduce speed in poorly lit areas.
- Avoid unfamiliar routes with heavy traffic when visibility is poor.
The Himiway D5 2.0 20" comes with an integrated 130 Lux/800-lumen front light and a rear light with a braking indicator.
These features help improve visibility, but riders should still use appropriate lighting and reflective equipment according to local regulations.
15. Don't Perform Jumps, Stunts, or Extreme Riding Beyond Your Ability
Fat tires and full suspension can make an e-bike more comfortable on uneven surfaces. However, they do not make every type of terrain or riding activity safe.
Some riders assume that a powerful motor and wide tires make an e-bike suitable for aggressive jumps, extreme downhill riding, and stunts.
This is a dangerous assumption.
The Himiway D5 2.0 20" features 20 × 4.0-inch fat tires, front suspension with 90mm travel, and rear suspension with 100mm travel. These features help absorb impacts and improve comfort, but they do not eliminate the risks associated with extreme riding.
What to do instead:
- Choose trails appropriate for your experience.
- Avoid jumps and stunts unless the bike is specifically designed for that type of riding.
- Wear appropriate protective equipment when riding off-road.
- Inspect the bike after riding over rough terrain.
- Check whether e-bikes are permitted on your intended trail.
- Avoid riding alone in remote areas.
Himiway's owner’s manual explicitly warns against jumps, stunts, and riding beyond your abilities.
A Simple E-Bike Safety Checklist Before Every Ride
You don't need complicated maintenance procedures to develop safer riding habits. A few basic checks can make a meaningful difference.
Use this checklist before heading out:
E-Bike Pre-Ride Checklist
- Wear a properly fitted helmet.
- Check tire pressure and inspect both tires.
- Test the front and rear brakes.
- Confirm the battery is securely installed.
- Check the handlebars, wheels, and pedals.
- Make sure the front and rear lights work.
- Check the display and throttle operation.
- Choose an appropriate pedal-assist level.
- Secure all cargo properly.
- Check the weather, route, and local riding regulations.
Is the Himiway D5 2.0 20" a Good E-Bike for Everyday Riding?
Himiway D5 2.0 20-inch eBike
A compact-wheel fat-tire e-bike designed for commuting, recreational riding, and different road conditions.
750W motor · 90Nm torque · 48V 15Ah battery
Here are some of its key specifications:
|
Specification |
Himiway D5 2.0 20" |
|---|---|
|
Motor |
750W geared hub |
|
Maximum torque |
90Nm |
|
Battery |
48V 15Ah (720Wh) |
|
Advertised PAS range |
Up to 70 miles |
|
Advertised throttle range |
Up to 40 miles |
|
Tires |
20 × 4.0 inches |
|
Front suspension |
90mm |
|
Rear suspension |
100mm |
|
Brakes |
Tektro hydraulic disc |
|
Bike weight |
80 lbs |
|
Maximum payload |
440 lbs |
|
Recommended rider height |
4'11"–6'3" |
The D5 2.0 20" combines a 750W motor, wide tires, full suspension, and hydraulic disc brakes. Its features provide a practical foundation for everyday and recreational riding, but safe operation still depends on the rider.
For beginners, starting with a low pedal-assist level, practicing braking, and understanding the throttle response are particularly important.
If you are comparing different models, you can also explore the full range of Himiway Electric Bikes .
Where to Find Himiway Black Friday E-Bike Deals 2026
If you are planning to purchase an electric bike, it is worth comparing available models, specifications, and promotional offers before making a decision.
Himiway's Black Friday E-Bike Deals 2026 campaign runs from November 1 through November 30, 2026. The promotion includes selected e-bikes and limited-quantity offers on eligible D5 2.0 series purchases.
The available discounts and gifts depend on the qualifying model, promotional terms, and remaining stock. Check the current offer before completing your purchase.
Himiway Black Friday E-Bike Deals 2026
Explore current electric bike offers and qualifying promotional gifts.
Frequently Asked Questions
1. What is the biggest mistake people make when riding an e-bike?
One of the biggest mistakes is underestimating the bike's speed and acceleration. New riders should start with low pedal assistance, practice braking, and learn how the throttle works before riding in traffic.
2. Is it safe to ride an e-bike in the rain?
Light rain may be manageable for many e-bikes, depending on their water-resistance ratings. However, heavy rain, flooded roads, and deep puddles should be avoided. Wet conditions also reduce traction and braking performance.
3. Should I charge my e-bike battery overnight?
It is not recommended. The CPSC advises riders to remain present while charging and never charge an e-bike battery while sleeping or away from home. Use the manufacturer's approved charger and follow its charging instructions.
4. Can I ride an e-bike without pedal assistance?
Yes. Many electric bikes offer a pedal-only mode. The Himiway D5 2.0 20" supports riding without motor assistance, allowing you to pedal like you would on a traditional bicycle.
5. Can I ride an e-bike on sidewalks?
It depends on local regulations. Some communities allow bicycle riding on certain sidewalks, while others restrict or prohibit it. Always check local rules and give pedestrians priority.
6. How often should I check my e-bike?
Check the tires, brakes, battery attachment, and lights before every ride. Perform more comprehensive maintenance regularly, following your manufacturer's maintenance schedule.